Mesh Wire Machine for Drying Wood Veneer Sheets

• Customization: Available
• After-sales Service: 1 Year
• Warranty: 1 Year
• Model NO.: MH-RD40L
• Heating Mode: Transmission
• Material Status: Wood Bucks
• Drying Medium: Superheated Steam, Air
• Operation Pressure: No
• Drum Number: Multiple
• Type: Mesh Type
• Machine: Mesh Machine
• Layers: 2
• Width: 2800mm
• Heating Section: 12
• Cooling Section: 2
• Convey Method: Stainless Steel Wire
• Veneer Humidity: 40-70%
• End Humidity: 5-10%
• Speed: Adjustable
• Weight: 65000kgs
• Transport Package: None
• Specification: 40 * 5.8 *2.5m
• Trademark: MINGHUNG
• Origin: China
• HS Code: 841939
• Production Capacity: 2000sets/Year
• Package Size: 4000.00cm * 580.00cm * 250.00cm
• Package Gross Weight: 65000.000kg

Product Description

 

                                  Mesh wire machine for drying wood veneer sheets 

 

 

 

Mesh wire machine for drying veneers moisture. For mesh machine, it can be different decks, width and sections to satisfy different drying capacity. 
its mesh is stainless steel wire, so rust protection. And we use big fan motor and radiator, to achieve better drainage. 
 

    

During the veneer drying process, a large amount of steam will be generated inside the dryer. If the steam cannot be discharged in time, it will affect the veneer drying efficiency and reduce the output of veneer drying.

MINGHUNG patented automatic control veneer drying moisture removal system, the whole The machine is controlled by computer PLC. According to the water vapor generated in the drying process of different veneers, automatic detection and automatic moisture removal are carried out.

There are a variety of sensing devices inside the veneer dryer, which convert the detection data into computer signals, and convert the computer signals into PLC signals. control.

The advantage of this design is precise moisture removal, automatic processing according to the dry humidity inside the veneer dryer, and avoiding the loss of energy inside the veneer dryer. Energy is saved and thermal efficiency is improved.

 

 

 

Beech veneer is light yellow, with clear texture and uniform texture. The density of beech is generally about 790kg/m³, and the hardness is about 5800N. The rear beech veneer has a smoother surface. Because it is cooking, the moisture content reaches %50-%60, and the moisture content is relatively high. If the moisture content of the veneer after drying reaches %0-%14, it takes about 10 minutes, so if the output of beech veneer drying is If there are requirements, special optimization of the dryer is required. MINGHUNG MH-RD2830L; MH-RD304HL These two models are veneer drying equipment optimized for beech veneer. For details, please contact us.

Veneer drying is very important for the production of plywood. After wood is produced into veneer through veneer lathe, the moisture content is 50-70%. Plywood production requires veneer moisture content of 8-%14. The moisture content of veneer is greater than %14, which brings negative The influences are:

1. It will increase the hot pressing time of the plywood blank in the hot press. The heating of the hot press is heated by a steam boiler or a heat transfer oil boiler. If the hot pressing time is increased, it is equivalent to an increase in heat loss.

2. If the moisture content is higher than %14, the veneer after glue spreading will seep out of glue during the hot pressing process, causing the plywood to crack.

3. If the moisture content of the veneer is 14%, the plywood blank needs to be dehumidified several times during the hot pressing process to remove the moisture inside the plywood blank. If the temperature is not properly controlled, there will be air bubbles in the semi-finished plywood, which will crack and cause the plywood to be scrapped.


Other type dryer-Hollow press dryer